U型槽模具?的形狀是多種多樣

U型槽模具的形狀是多種多樣的,十分常見的就是U型的,是因為這種形狀不但排水效果好,而且用地面積小,能夠很好的節省土地資源,也能夠讓水資源處于一個良性循環當中。U型槽模具的尺寸以及規格進行模具的生產工作,U型槽模具廣泛應用于各個排水以及灌溉工程中,更多的使用地區集中在東北、西北以及其他地區。U型槽模具的使用范圍很廣,包括了公路、高速高鐵等多種交通建設當中,在道路的兩側作為重要的排水設施,能夠及時將上面的雨水排出去,保證交通的安全有序運行,同時它也會在坡道建設當中使用,有著穩固土地的作用。

The shape of U-groove mold is various, and the most common one is U-shape, because this shape not only has good drainage effect, but also has a small land area, which can save land resources and keep water resources in a virtuous circle. The size and specification of the U-groove mold are used for the production of the mold. The U-groove mold is widely used in various drainage and irrigation projects, and more use areas are concentrated in the northeast, northwest and other areas. The U-groove mold has a wide range of applications, including roads, high-speed high-speed rail and other traffic construction. As an important drainage facility on both sides of the road, it can drain the rainwater above in time to ensure the safe and orderly operation of traffic. At the same time, it will also be used in ramp construction, which has the role of stabilizing the land.

U型槽模具結構呈現整體的U型，一般兩側會帶有小翅膀，這樣上面可以放置蓋板等，U型構造有利于流水等。流水槽模具多為矩形，種類較多，在使用中可以根據工程需求選擇模具的規格，在具體的使用中，往往會因為模具的規格尺寸差別，相應的在施工方法上做出一些改變，以保證使用方便。比如較為小型的流水槽模具大多是只由內模和外模組成的，采用立模的形式進行生產，因此其拼接就更為簡單，注意在拼裝好模具后需要檢查連接處是否留有縫隙，如果沒有縫隙再進行后續的生產，因為如果螺栓沒有擰緊而留下細小的縫隙.可能會流失混凝土中的水分，使水的配比過低，影響混凝土整體的比例，導致生產出的混凝土集水槽質地不均勻。然后在流水槽模具刷涂脫模劑，注意脫模劑要均勻地刷涂在模具的內表面，再注入按照固定比例提前調配好的混凝土。注意在注入混凝土的過程中往往會因為高度差給混凝土泥漿帶來一定的沖擊力，包裹著空氣混入混凝土中，所以需要充分震動將氣泡排出，然后等待混凝土完全凝固后再拆除模具，為了運輸的方便，往往需要等待以上，防止集水槽預制件因運輸的顛簸而變形。

The U-groove mold structure presents an overall U-shape. Generally, there are small wings on both sides, so that the cover plate can be placed on it. The U-shape structure is conducive to flowing water. Most of the flow channel molds are rectangular and have many types. During use, the specification of the mold can be selected according to the engineering needs. In specific use, due to the difference in the specification and size of the mold, some changes will be made in the construction method to ensure convenient use. For example, most of the smaller flow channel molds are only composed of the internal mold and the external mold, which are produced in the form of vertical mold, so its splicing is simpler. Note that after the mold is assembled, it is necessary to check whether there is a gap at the joint. If there is no gap, subsequent production will be carried out, because if the bolts are not tightened, small gaps will be left The water in the concrete may be lost, so that the water ratio is too low, affecting the overall proportion of the concrete, resulting in uneven texture of the produced concrete sump. Then brush the mold release agent on the water trough mold. Note that the mold release agent should be evenly brushed on the inner surface of the mold, and then inject the concrete prepared in advance according to the fixed proportion. It should be noted that during the process of concrete injection, the height difference often brings certain impact force to the concrete slurry, which is wrapped with air and mixed into the concrete. Therefore, it is necessary to fully vibrate to discharge the bubbles, and then wait until the concrete is completely solidified before removing the mold. For the convenience of transportation, it is often necessary to wait for the above to prevent the prefabricated parts of the water collecting tank from deformation due to the bumps of transportation.